Please read this section carefully before setting up your Watches, You can find Winding instructions below for Automatic and Manual Winding Watches
Winding Instructions for Rolex and Other Automatic Movement Watches.
Instruction #1
For most watches you must first unscrew the crown counter clockwise (12 O Clock Direction). The stem will spring out by itself. Rotate the crown clockwise about 30 revolutions. This will give the watch an initial pre charge. If you do not wear the watch on a daily basis you will need to charge your watch as it will de-wind as it sits. While wearing the watch the kinetic movement maintains the watches power and keeps the time and charge. You will never need to replace a battery as the watch is fully mechanical. We do recommend that you have your watch serviced once a year, as all automatic replicas require. Any watch repair shop should be able to do this for your. Our automatic replicas come with a Japanese Miyoca movement. One of the highest quality Japanese movements in todays market.
Instruction # 2
Please Pull the Screw of the Watch Right till the End until you can move it freely where the Minute and The Hour hand also moves freely. Once you’ re at this point, please push the Screw in gently until it goes slightly inside. At this point you will be Rotate the Screw Freely but the Minute and Seconds hand will not move anymore while turning the Screw. Once at this point, please turn the Screw of the Watch in the 12 O Clock Position (Upwards Position) approximately 10-15 times. While performing this step you will hear the machinery inside the Watch gearing up against each other. Please note that if you hear a very Smooth noise or do not hear anything at all that means you are winding the Watch incorrectly. You need to perform this step once in a while (Once in every 2-3 Days) since it helps keep the watch running much longer than when you do not wind the Watch at all and make the Watch move by Shaking the Watch alone
Winding Instructions Panerai and Other Manual Winding Movement Watches.
Please turn the Screw of the Watch in the Upwards Direction (12 O Clockwise Direction) while it is still screwed right inside. Please turn the Screw approximately 20-30 Rounds until you see the movement in the Seconds hand. If your Watch is Equipped with a Power Reserve Indicator please Follow the directions above until the Power Reserve Indicator is Full.
Setting Date and Time.
Please unscrew the crown (setting knob) of the watch. Turn the Knob from up to down (downwards) you will feel the knob loosen and then it will pop out gently.
Pull out the pin very gently and turn downwards OR upwards in some watches to set the date. If you have a Day and Date watch turn upwards to set the day of the week.
Please make sure you push turn the pin tightly because most cases of Water Damaged watches are caused due to the pin being screwed up not tight enough.
The Method of Usage of Six-needles
1. The second hand didn’t run when you received the mechanical-watch, it was natural, please noted it! And now the operate was begun: First please released the middle of button, than circumgyrate the up- clockwork spring when the button was released. I suggested you that you should circumgyrate the new watch or the watch which had a long time no use at least 30times, so it can give more power for those watches, and avoid form the stopping or nicety.
2. Draw-back the hour hand, circumgyrate it twice till stop on 7' clock. Why should we do that? Because the watch would be blocked before the operate of the new watch. I also suggest that should operate it if the watch leave unused. Then draw the button to operate the date, 1-30th, if the month has 30days, you just operate through the 31st by your hand. (Please note that the calendar is operated in 24' clock. if the calendar is operated in daytime, you just circumgyrate 12 hours by your hands is ok!)
3. Draw the button in second gear, is to operate the time.
4. The button on the top right corner is to operate week. The 9' clock would denote in small dial plate. The function of the week skipped seven times or two times than seven. Viz. skipped once in morning and skipped once in afternoon.
5. The up right corner is to operate the month, the 3' clock would denote in small dial plate. The month skipped 12 times every circle. The calendar skipped 31time every circle.
6. The 6' clock would denote in small dial plate in 24hours.It follows the hour hand when operate the hour hand, so the function is 24hours system.
7. Do not operate the time and the function on 23' cloak to 5' clock, avoid from destroying the work of the watches.
The Method of Usage of Eight-needles
1. Circumgyrate the up- clockwork spring when the button was released. I suggested you that you should circumgyrate the new watch or the watch which had a long time no use at least 30times, so it can give more power for those watches, and avoid form the stopping or nicety.
2. Draw the button in second gear, is to operate the time
3. The button on the top left corner is to operate year (2007-2018), starboard in the small dial plate of 12 ‘o clock.
4. The button on the top right is to operate month.(JAN.:?FEB.:?MAR.:?APR.:?MAY.:?JUN.:?JUL.:?AUG.:?SEP.:?OCT.?NOV.: DEC. :?.), nearside in the small dial plate of 12 ‘o clock.
5. Every 30minutes would circumgyrate 6’c clock to 12' clock; it would be circumgyrated as the operated time.
6. The button of up right corner is to operate calendar, it denoted by the needle which have a fork.
7. The button of up left corner is to operate week, it denoted by small dial plate in 9’c clock.
8. The 6' clock would denoted in 24 hours, and circumgyrate one circle in every 24hours.
9. Do not operate the time and the function on 23' cloak to 5' clock, avoid from destroying the work of the watches.
The Method to Operate Auto-mechanical Five-needle Watch
1, circumgyrate the up- clockwork spring when the button was released. I suggested you that you should circumgyrate the new watch or the watch which had a long time no use at least 30times, so it can give more power for those watches, and avoid form the stopping or nicety.
2. Then draw the button to operate the date, 1-30th, if the month has 30days, you just operate through the 31st by your hand. (Please note that the calendar is operated in 24' clock. if the calendar is operated in daytime, you just circumgyrate 12 hours by your hands is ok!)
3. Draw the button in second gear, is to operate the time
4. The button of up left corner is to operate week, it denoted by small dial plate in 9' clock.
5. The button on the top right is to operate month, nearside in the small dial plate of 3‘o clock.
6. Do not operate the time and the function on 23' cloak to 5' clock, avoid from destroying the work of the watches.
The Method to Operate Auto-mechanical Three-needle Watch
1. Circumgyrate the up- clockwork spring when the button was released. I suggested you that you should circumgyrate the new watch or the watch which had a long time no use at least 30times, so it can give more power for those watches, and avoid form the stopping or nicety.
2. Then draw the button to operate the date, 1-30th, if the month has 30days, you just operate through the 31st by your hand. (Please note that the calendar is operated in 24' clock. if the calendar is operated in daytime, you just circumgyrate 12 hours by your hands is ok!)
3. Draw the button in second gear, is to operate the time
4. Do not operate the time and the function on 23' cloak to 5' clock, avoid from destroying the work of the watches.
